Polymer80 bit size - Glock Talk
2018年3月15日 · Ronin's Grips - Polymer80 Pistol Frame M35 Drill Bits 3mm & 4 mm - These quality drill bits are sized for drilling Polymer80 pistol frames for their pins. This package includes one 3mm drill bit (approx. 2.95-2.97mm) and one 4mm drill bit (approx. 3.95-3.96mm).
P80 drill bit question - Glock Talk
2021年2月27日 · Normally the 5/32" bit works just fine for the 4mm trigger pin. And yes you do have to ream the holes drilled with the 7/64" bit out with either a good #32 or 3mm bit by hand. I'm a retired tool and die maker and am use to drilling hole slightly undersized and then reaming them to the correct size for pins. Old habits die hard.
Front Sight Screw Rounded - Glock Talk
2025年1月10日 · I tried to install a Night Fision front sight which I managed to loosen a little bit with a 3/16 socket, am I screwed or can a qualified Glock armorer get that screw off and install the new sight, sorry about my rant but I'm so frustrated with the whole situation I'm in. Any thoughts on this would be greatly appreciated. Thanks, Scott.
Stripped screw heads in red dot sight... - Glock Talk
2023年4月11日 · get a bolt extractor,,drill the stripped torx head for a little depth. Make sure your tiny drill will match the tiny extractor. Find out the size of the screw Bolt The worn out torx should get your drill bit close to center,,be careful with your drilling depth,,of course don’t damage the threads with a to large of a width drill
43x MOS vs CC9 - Glock Talk
2024年11月21日 · If you use the 12 rd mag the Glock is only longer by the base pad and a half inch in length, which to me isn't much. I actually would have preferred the CC9 to be a bit longer in the barrel. I don't like two finger grips so my sweet spot is 5" in length. The 365 is a closer match in size, but I've had them and sold them.
Drilling a hole in the Glock trigger bar... | Glock Talk
2005年6月1日 · I put the trigger bar in a vise and use my 8" drill press with a 5/64" bit. Two regular high speed drill bits, one Titanium, quad point drill bit and two hours later, the new hole is not even half way through the trigger bar. ;P Damn, the Glock trigger bar is made of some hard stuff. What am I doing wrong?
How easy is it to strip the MOS screws? | Glock Talk
2017年2月25日 · It was easier than that as I remember. Use the correct bit/driver head but one size larger. Gently but firmly tap it into the stripped head. Once tapped in then with firm grip loosen the screw (the tapping helps loosen the threads a bit and heat might help). Another video had you use a strip of rubber band between the stripped head and the bit.
Polymer 80 Trigger Mechanism Housing | Glock Talk
2022年3月14日 · Get the drill motor running. Cut off the twisted portion of the drill bit. Now shape a nice taper on the end of the drill bit shank. Done. Put some lube on the slave pin and tap it into your frame while pressing in the TMH/RRM. With the correct size punch tap the slave pin to …
Need advice from experienced DIY grip reduction people-PLEASE
2019年2月18日 · Build it back up with epoxy, shave it so it's the right shape, then use a drill bit, by hand, to stippole. You only need to do this in the built up area. It will not be perfect, but you'll have your frame back. I'm building my third wooden kayak - my own design - my plans.
Glock 21… | Glock Talk
2024年12月31日 · I tend to shoot 45 through a Glock 30S with a 21 mag and x-grip, or a 1911. I like the 30S and shoot it pretty well. The 21 is a bit more accurate. But the grip is really big. Even for my size L hands I feel like I am continually shifting my grip.