Are spacers bad for the car??? - Jeep Enthusiast Forums
2007年8月8日 · Wheel spacers are fine as long as you use the correct ones. All civilian Jeeps have had hub-centric axles forever, and a lot of people don't understand that. It matters a great deal which spacers you use, there are bad wheel spacers out there. The spacers should be machined out of a high-strength alloy such as the T6-6160 used by SpiderTrax.
Do wheel spacers really damage wheel bearings?
2013年1月4日 · Wheel spacers multiply the amount of stress on the bearings and other components in your suspension, adding force as a lever. IIRC, the angle in wheel bearings is designed to cancel or counteract this force in stock configurations, but if you move the center circumference of your tire away from stock, you add stress.
Wheel Spacers....good or bad | Jeep Enthusiast Forums
2012年10月2日 · same idea yes. But still effect scrub radius. Wheel spacer is usually 1.25"+ that coupled with a 3.75 bs wheel and you have effectively gone to a 2.5" bs. About the Limits of wheel bs that I've seen. Either way it effects scrub radius. …
The correct way to use wheel spacers | Jeep Enthusiast Forums
2014年3月1日 · Jeeps use "hub centric" wheels which wrap tightly about the raised center hub of a Jeep axle. GOOD wheel spacers have both a recess on the backside to fit tightly around the axle hub, and a raised ring on the outside to fit the wheel recess. Many, many wheel dealers ignore this basic feature when they sell aftermarket wheels.
Wheel Spacers - Jeep Enthusiast Forums
2004年6月9日 · are wheel spacers bad for the jeeps axles (bearings seals etc.) i know they have stronger axle, dana 44 vs. the dana 35. but i was curious, i was going to lift my jeep with the rusty's 3.5 kit. and use 31's (mud terrains) and was curious if it would be bad or good to put a spidertrax wheel spacer kit on it. i dont want it hanging too far out, just enough for a …
Wheel Spacer Installation DIY - Performance and Tuning
2017年9月2日 · Use your original factory bolts and thread into each of the reinforced threaded hold of the spacer. Tighten the bolts down in the same way as for the spacer bolts. "Star" pattern sequence. Torque 150nm. 7. Lower your car from jacked position and using your torque wrench, go through each of the 5 bolts again to make sure they are tighten to spec.
Wheel Spacers - Tyres and Rims - Mycarforum
2004年8月26日 · i had 2.5" spacers for the rear and 1.5" for the front. looks nice but if go for thinner ones if you wanna avoid having to do wheel balancing every now and then. Link to post Share on other sites
Wheel Spacer - Made in China | Jeep Enthusiast Forums
2011年8月2日 · The wheel spacers look nicely made cosmetically, at least. Don't know about the strength even if the material is 6061T6 aluminum. The lug nut looks OK (at least in the picture). What isn't made in China these days? I bought a new Daisy BB gun and it's made in China too.
Wheel spacers - Jeep Enthusiast Forums
2011年11月1日 · I ran 2" wheel spacers on front and rear of my 5 for years. Never had a problem. I ran 35"x12.5 MT baja claws. I just changed to 33x12.5 BFG KM2 on Mickey Thompson rims. Took the wheelspacers off since the backspace of the rim is far enough for the tires not to rub. I will tell you when I put the wheel spacers on, the jeep handled better.
Wheel Spacers VS new Wheels Good? Bad? Opinions...
2009年2月22日 · Wheel spacers are fine. If you are getting wheel spacers I would go with Spidertrax. Ideally though, it would be better to get new wheels with the backspacing you want. If you don't mind steelies, you can get a set of steelies for about the price of wheel spacers. I run the 1.25" Spidertrax spacers on my Canyons with 5.5" of bs to clear my ...