Herman Nelson H-1 Heater | SteelSoldiers
2020年2月25日 · Boston/mass. I am looking for a manual for the H-1 heater. It is a gasoline fuel heater used by the USAF to preheat engines and or the interior of planes. It has a single cylinder gas engine to drive the blower and generates up to 400,000 BTUs. The unit was last used in 1987 at the Westover AFB in Mass.
H-1 Ground Support Heater, NSN 4520-01-056-4269 - SteelSoldiers
2019年4月26日 · I just brought home an older ground support heater, NSN 4520-01-056-4269, manufactured by Davey Compressor Company of Cincinnati, Ohio. It's definitely a bit rough around the edges, but it looks like all of the essential equipment is there and in-tact. The hour meter reads out about 1400 hours, so it seems that it was rather well-loved in its day.
Herman Nelson type heaters. 400,000 BTU - SteelSoldiers
2020年2月29日 · Location. Burgkunstadt, Germany. There are more then several different types of Herman Nelson heaters. These two TM's cover some of the 400,000 BTU heaters. The TM's are TM5-4520-208-15 and TM5-4520-208-25P.
MEP003-A Manifold heater wiring Please Help. | SteelSoldiers
2018年1月9日 · Hello all. I am brand new to the Forum, and hail from the eastern slope of the rockies, near the Royal Gorge. I have an MEP003-A that I just reconditioned the injectors in, and the machine was received with 3 broken glow plugs. I don't want to pull heads, so now need to get manifold heaters...
Its cold outside lets talk Heaters, H81, H82, H83, etc.
2014年11月21日 · The easiest fixes to try out on these H81 H82 heaters that I have found from the fault of the red light of death. Dismount the K8 relay from its hiding spot behind the control panel (4 phillips skrews) Remove the 2 skrews that mount the P2 connectors to the mounting bracket. The plug has J2 printed on it.
M1035A2 soft top - SteelSoldiers
2024年7月3日 · It appears intact from the one picture, but it also looks a bit weathered (i.e., not fresh). The trip home won't be kind to anything but the freshest of tops. With all this said, the M1035 tops can't be too common if you needed one...but that works both ways...not many guys are going to need one. My $.02. majorhavoc67. Jul 3, 2024.
M35A2 trouble shooting starter/electrical problem - SteelSoldiers
2015年4月18日 · Only a couple weeks ago. Will try to go through what happened. 1. I connected the short jumper wire on the batteries ( I disconnect the batteries between runs) 2. Turned on main switch, get power. Engine stop still pulled. 3. Pushed start button.
M135 / m211 gmc parts - SteelSoldiers
2009年10月11日 · Location. Cantley Quebec. There ar eonly a few people selling the old M135/211 parts are getting rare. Everytime I see the parts I buy them and store them. The hardest parts to find are body parts. I have 2 transmissions and a lot of various engine parts.
Trouble removing freeze plug (pic included). Please help!
2012年2月8日 · An oxy/acetylene cutting torch will do the job. Don't use the oxy lever, just heat the freeze plug until it melts/burns out in one small spot. You'll need to be skilled. Feb 8, 2012. #9.
Mechanical Booster Pump "making oil" - SteelSoldiers
2012年5月27日 · With Dylan's advice, I was able to get the engine moved far enough away from the steering box that I was able to remove the booster pump. Remove your heater box (if equipped), unhook fuel lines on booster pump, then unhook the front mounts and drivers rear mount. I lift the front of the engine, then pulled it towards the passenger side and that ...