Johnson 15HP Outboard | Hearth.com Forums Home
2013年6月10日 · So far I'm liking the Johnson/Evinrude design on this motor, it's simple and easy to work on. Toggle signature Quadrafire 3100I (Year 8) and Englander 13NCL (Year 6) Stove Owner
What size generator would I need to run a 10HP electric motor?
2009年12月8日 · My HP calculator tells me that 10HP=7456.9987 watts. That's running watts and the startup current will be the bugger. Note that folks using little tiny 1 HP well pumps report needing no less than a 5000 watt genset even though 1HP = 745.6999 watts. A single phase 10HP motor is pretty rare. That motor will suck major amps at startup.
Huskee 22 Ton replacement motor... - Hearth.com Forums
2016年1月11日 · Heatmaster MF5000 John Deere 5410, Ford 7600, International 574, Chevrolet 2500 HD crewcab Huskee 22 Ton Echo CS-590 Timberwolf, Echo CS-310, Stihl 025
Grundfos 15-58 Failure? | Hearth.com Forums Home
2014年12月26日 · I haven't taken apart a 15-58, but I have a Taco and Wilo, and on these the motor with impeller unbolts from the impeller casing. No need to remove the plumbing side of the circulator. Just the motor impeller cartridge may be available, but they could be removed from a new 15-58 and installed on the old plumbing as best as Iknow.
US Stove auger motor part # 80488 - Testing the RPMs
2010年2月1日 · Note: As a base measurement, the original OEM Whitfield auger motors that are 1 RPM motor takes 60 seconds for 1 revolution. After market auger motors can vary, I have seen 1.2 RPMs on some! The US Stove Volgozang pellet stoves come with a 1.5 RPM auger motor so finding a replacement motor with the same RPMs is not that easy.
Stihl 064 AV vs. 056 AV Magnum II | Hearth.com Forums Home
2012年7月3日 · 064 AV: 85 cc, 6.5 hp, 15.2 lb, 12k rpm max 056 AV Mag II: 94 cc, 6.7 hp, 18.3 lb. I think the standard 056 was "only" 81 cc's. I've read the Bosch ignitions are prone to failure, and damn expensive to replace. Some later saws had an SEM ignition which apparently more reliable.
Buck 28000 Fan/motor | Hearth.com Forums Home
2012年1月24日 · That same condition with Rutland mounted on the stove adapter reads 450. If my stove fan kicks into medium it putting out some big time heat. When I bought my stove I went ahead and replaced the 3 speed motor, 3 speed thermostat and new wiring kit. But to answer your question my fan motor is the same Fasco and 3 speed as the one you have.
25-PDVC auger motor overheating?? - Hearth.com Forums
2012年4月12日 · It is a heavy duty motor 1 1/16" field stack vs the 3/4" Merkle-Korff. I first put the 2 RPM motor on the upper auger and it worked OK but tended to overfeed. I then moved the 2 RPM motor to the lower auger and put the Original revived lower Englander/Merkle-Korff motor on the upper auger and will run it to failure.
johnson furnace question | Hearth.com Forums Home
2011年12月27日 · The Johnson furnaces are close if not the same furnaces from usstove. If the unit has forced draft you should have a relay center, and a limit/control for the blowers. A thermostat is tied to the relay center which controls the forced draft.
Harman XXV auger motor,sprocket & chain removal & replacement
2018年5月1日 · I'm looking for a video that shows how to remove & replace the auger motor,sprockets, chain & the auger itself. I've been getting banking noises this winter and found that the set screw on the auger motor sprocket was loose. After tightening the set screw it got significantly better but still does it, just less frequently.