Taylor Neck Joint Bolt? - Unofficial Taylor Guitar Forum
2012年12月5日 · Taylor guitars made before the advent of the NT neck in 1999, (the NT neck was phased in over time so not all guitars made after 1999 have the NT neck) still had more than one bolt and though they didn't have the easy neck adjustability of the NT design, were still less costly to reset than the traditional Martin design.
Taylor Neck vs. Scarf neck - Unofficial Taylor Guitar Forum
2020年10月30日 · A scarf joint is how the headstock is attached to the neck, as well as the heel. The NT neck is now just referred to as the Taylor Neck and is standard on all Taylors except the Baby and Big Baby models. The scarf joint they’re referring to isn’t instead of the bolt on neck system. Scarf joints exist on all Taylor models.
NT Neck Shims - Unofficial Taylor Guitar Forum
2014年11月11日 · For example, if you need some extra back tilt of the neck and remove a shim stamped "06" from the neck-to-body joint, then you would replace it with a shim stamped "04", slightly thinner than the original factory installed shim. That changes the neck angle in small repeatable increments.
Which Taylors have glued on headstock - Unofficial Taylor Guitar …
2012年7月15日 · The question is how the headstock joint is configured. Taylor currently uses a glued scarf joint which joins the face and the back of the headstock at a long oblique angle. The finger joint you ask about was lower on the neck as shown in the picture on this thread. Taylor used the finger joint for about two years between 2006 and 2008.
What makes the 90s Taylor 810 special - Unofficial Taylor Guitar …
2023年5月15日 · For me, another sub-division in the line is 2007: neck joint became the much more attractive scarf joint over the finger (aka Frankenstein) joint. Yes, aesthetics matter (even nicer is the aforementioned pre-NT with no neck joint as it's a 1-pc beauty). Also in 2007 was the ES1.2 where the preamp went to a 9v and was revoiced and is far better ...
Neck joint - is this normal? - unofficialtaylorguitarforum.com
2013年2月28日 · I just bought a used 2006 Taylor 414ce. I have a question about the visible neck to headstock joint. I've seen this on a few other Taylors but more often, I see necks that have been finished so that the joint does not show like this.
what year did the fingerjoint at the neck go away?
2013年8月16日 · My GC3 is a 2007 and has a scarf joint, so I think that coincides with what is said above. I know that in 2004 all Taylor's, regardless of series, had finger joints. So, to answer your question, the finger joint went away in '06 or '07. Now, when did that finger joint replace the solid neck with headstock wings?
Taylor Warranty, does it cover neck reset? - Unofficial Taylor Guitar …
2013年8月20日 · A neck reset would be covered if there is a defect in the original setting such as the wrong shim used. I would tend to think that a Taylor that is not new (or very close to being new) would not be covered for a neck reset since humidity and other wear factors that could be considered normal would not allow it to be covered.
Taylor necks
2013年4月28日 · If I recall correctly, it was in the Taylor NT video and I believe that 3 necks can be made out of one 4"x4"x4' piece of Mahogany. The pre NT Mahogany neck had headstock wings, so technically it was still a 3 piece neck, but if the grain orientation was not correct when the lumber was cut, that wood was rendered all but useless for a neck.
Unusual half-hoop bracing in a Baby Taylor - Unofficial Taylor …
2023年2月8日 · It is a feature that was brought down from our Acoustic Bass design and it enables us to attach the neck to the body of the guitar by way of the sides, rather than the top. This Baby Taylor neck joint design was changed in June of 2001 to a design that is similar to the neck joint design of the Big Baby Taylor. The "Wall" was eliminated entirely.